PRO
STIHL EXTENDS CORDLESS POLE PRUNER RANGE WITH MOST POWERFUL MODEL

STIHL has extended its range of lightweight cordless pole pruners with the introduction of the new HTA 135, the manufacturer's most powerful model to date, designed for professional arborists, landscapers and commercial enterprises.

Quiet in operation and perfect for working in noise-sensitive areas, the HTA 135 comes fitted with a 3/8” PMM3 semi-chisel, anti-kickback saw chain providing precision, high cutting performance and low-pinch tendencies. A branch hook offers stability for a more accurate cut and helps to remove caught-up branches easily. 

The HTA 135 also features a square telescopic shaft that can be quickly adjusted between 285cm and 405cm using the new twist and click adjuster. A square shaft for increased rigidity prevents twisting and deflection, delivering a precise cut even at full extension. 

In addition, operators can simply manage the three-speed selection levels thanks to a comfortable control handle with an intuitive LED display. The HTA 135 can also be worn with an RTS harness to take the weight of the tool away from the arms, distributing it across the shoulders and waist.

When used in conjunction with STIHL’s AP 300 S battery system, the HTA 135 has a run time of up to 45 minutes.

For more information on the STIHL HTA 135 and its extensive range of cordless pole pruners, please visit www.stihl.co.uk

Votes: 0
E-mail me when people leave their comments –

You need to be a member of Landscape Juice Network to add comments!

Join Landscape Juice Network

Open forum activity

Oliver clarkson posted a discussion
Evening what products are people using for black spot on roses, I'm about to run out of my current product which isn't available any more. many thanks 
13 hours ago
Graham Taylor replied to Jamie's discussion Stihl BG86c problems
"I just use a couple of pieces of paper for the gap and then just rotate the flywheel to ensure its not rubbing anywhere.  I set it up when the magnets are pulling the coil onto it with the paper as a sandwich between the two..................holds…"
13 hours ago
Honey Badger replied to Jamie's discussion Stihl BG86c problems
"You're welcome. 
Im glad you got it working again."
15 hours ago
Jamie replied to Jamie's discussion Stihl BG86c problems
"Thank you for your replies. As it happens, i just re-alligned the ignition coil slightly just to get it slightly closer to the fly wheel as i noticed one side had a bigger gap than the other, and fingers crossed it's been ok today so far. It does…"
17 hours ago
Honey Badger replied to Jamie's discussion Stihl BG86c problems
"Replace there wiring you've probably worn out the kill switch. If it is a flywheel problem stop yanking the pull chord so hard, thats what shears of the flywheel key. I've had three bg86 they get a bit unreliable after 4-5 yrs. They all still run,…"
20 hours ago
John F replied to John F's discussion Service Schedule Stihl Cordless Hedge Trimmer ?
"Thanks Tim for the useful information , definitely worth mentioning also useful reminder to grease the gears regularly  
I must admit I sometimes forget with my more expensive kit which has the grease thread the grease soons dries out .
My Stihl…"
22 hours ago
Honey Badger replied to Jamie's discussion Stihl BG86c problems
"Get the flywheel off is tricky. Strip down both sides of the machine there's two opposing compression nuts you have to loosen the one on the fly wheel side. Use a punch and hammer to gently slide of the compression nut, there's a centre point the…"
22 hours ago
Honey Badger replied to Jamie's discussion Stihl BG86c problems
"Use a piece of cut plastic milk bottle to get the space right between the ignition coil and flywheel. The flywheel could be the problem. There's key on the flywheel that shears off and knocks the engine timing off. You have to remove the flywheel…"
23 hours ago
Tim Bucknall replied to John F's discussion Service Schedule Stihl Cordless Hedge Trimmer ?
"All the stihl kit I've got has grub screws for greasing, and stihl do grease in tubes like toothpaste.  Take the screw out (torx) and screw the tube in, squeeze some in.  Should be done quite regularly.  Also on shaft drive machines you should take…"
yesterday
Jamie posted a discussion
Hi all, hope this is in the correct thread.So i've had some BG86c blower problems recently. Long story short, i've replaced the carb with a genuine Stihl carb as my previous one wasn't priming, everything was fine once replaced but on full throttle…
yesterday
Honey Badger replied to John F's discussion Cherry Blossom Tree
"If it's right by a boundary wall it sadly needs to come out. Cherries are one of the worst for causing subsidence. People Are such idiots when it comes to planting tree's."
yesterday
John F replied to John F's discussion Cherry Blossom Tree
"Yes it's not always easy to do the right thing for the tree unfortunately whoever planted it put the wrong tree in the wrong place right next to a boundary wall when it was just a small tree .
Once it's pruned I  can't see it adding any value as it…"
yesterday
Peter sellers replied to Ben Hattersley's discussion Pricing for School grounds maintenance
"Ben, seems that you are in a strong position as you are well thought of by the school as you aren't the obvious choice to quote for something which is not your main business. Are they asking other contractors who do this type of work to quote? If…"
Thursday
Ben Hattersley replied to Ben Hattersley's discussion Pricing for School grounds maintenance
"Yes it seems to be mine field! The school arent happy with the current contractors and to be honest i wouldn't be either. The main concerns of the school are that they are paying for the contract but very little gets done.
Because i try stay away…"
Wednesday
Jim Mileman is now a member of Landscape Juice Network
Wednesday
Honey Badger replied to John F's discussion Cherry Blossom Tree
"Can't say I've ever seen silver leaf in 22 yrs because I don't prune prunus in the winter. The only dease I've seen on cherry is a die back due to old age. With exception a fungal thing that was poor soil related and did recommend to customer not to…"
Wednesday
More…

Stihl BG86c problems

Hi all, hope this is in the correct thread.So i've had some BG86c blower problems recently. Long story short, i've replaced the carb with a genuine Stihl carb as my previous one wasn't priming, everything was fine once replaced but on full throttle…

Read more…
6 Replies · Reply by Graham Taylor 13 hours ago
Views: 58