A Barnstaple construction company has been fined for safety failings after a ground worker was seriously injured when he stumbled from an excavator and fell down a five metre bank at a construction site in Middle Marwood.

The 65-year-old, who does not want to be named, suffered three fractured vertebrae, broken ribs and sternum, lung damage and a head wound that required stitches in the incident at a cottage undergoing renovation on 6 October 2011.

He was in intensive care for three weeks, has yet to make a full recovery and is unlikely to work again.

Barnstaple Magistrates' Court heard today (20 March) that his employer, G Loosemore and Son Ltd, had been contracted to build a two-storey extension at the rear of a cottage.

The ground worker was engaged in excavation work on land that sloped steeply upwards. An investigation by the Health and Safety Executive (HSE) found that his excavator was working on a level of ground at approximately roof height with the cottage in order to dig out material to make way for a terrace area and exterior steps leading to upper garden levels.

He needed to change the excavator's bucket during the work, but as he exited the cab he stumbled. He tried to steady himself by grabbing hold of a handle attached to the lift arm, but it came away in his hand and he fell approximately five metres down a slope and onto the path behind the cottage. He hit his head on a large stone as he fell and was knocked unconscious.

HSE established that there was no edge protection to prevent a fall to the area behind the cottage, and no steps were taken to support the excavation prior to the later installation of a supporting wall. The investigation also identified that there had been several falls of material from the main excavation area before the worker fell. These should have served as a warning, but no action was taken.

A Prohibition Notice was subsequently served to prevent any further excavation work at the site until a competent person had made an assessment and provided a safe system of work.

G Loosemore & Son Ltd, of Roundswell Business Park, Barnstaple, Devon, was fined a total of £12,000 and ordered to pay £11,210 in costs after pleading guilty to breaches of the Work at Height Regulations 2005 and the Construction (Design and Management) Regulations 2007.

Speaking after the hearing, HSE Inspector Annette Walker said:

"The dangers of working at height without adequate edge protection, and the risks associated with excavation collapse, are very clear. Yet companies and individuals continue to take risks and cut corners.

"In this case, significant harm occurred in respect of a fall from height. G Loosemore & Son Ltd could and should have done more to prevent the fall from the top of the bank, but this was only addressed as a consequence of the incident.

"There were a number of collapses of material prior to the fall that should have prompted the company to take earlier action, but these warnings were ignored. It illustrated there were serious risks, but they were disregarded.

"Today's prosecution should remind all involved in excavation work, or general work at height, of their legal duties to safely manage activity and provide the necessary protection."

Further information about working safely at height can be found on the HSE website at www.hse.gov.uk/falls. Information on excavation safety can be found atwww.hse.gov.uk/construction

Votes: 0
E-mail me when people leave their comments –

You need to be a member of Landscape Juice Network to add comments!

Join Landscape Juice Network

Open forum activity

M Olsson posted a discussion
Hi people,Last year I bought several pieces of equipment including a TF 325 tiller. It's been built but never used, infact- I haven't even put oil or petrol in it, nor have I started it. It's been sitting in my shed since September last year. If…
15 hours ago
Adam Woods replied to Dan Nate's discussion Charging Stihl tools from the van
"Thats exactly what I did for about 6 years... unplug it when not in use, and get them all charging when driving between jobs"
17 hours ago
Fusion Media posted a blog post
Etesia UK recently welcomed dealers from across the UK and Ireland to an insightful and engaging dealer day at Primrose Hill Farm in Oxfordshire. Attendees gathered to explore Etesia’s latest product innovations, gain industry insights, and connect…
20 hours ago
Fusion Media posted a blog post
Agrovista Amenity is pleased to announce its appointment as an approved distributor of Lanzarta, the newly authorised solution for controlling Hylobius abietis (large pine weevil) in Sitka spruce and other pine woodland.The recent Emergency…
21 hours ago
Dan Nate replied to Dan Nate's discussion Charging Stihl tools from the van
" Thanks gents - I was thinking an inverter from the cigarette ligher might work but then, as Nick says, I was also thinking it might be electrically dubious."
21 hours ago
Billybop replied to Dan Nate's discussion Charging Stihl tools from the van
"As Nick says, best just to buy more battery packs. The other option would be to take some kind of rechargeable mains voltage power bank to run a charger from. But that also could end up being more trouble than it's worth"
yesterday
Nick @ NM Garden Services Ltd replied to Dan Nate's discussion Charging Stihl tools from the van
"You need a pure sine wave inverter. We did fit 2 vans out with them, wired into the battery and with the correct fuses.
They would happily run a van battery flat if you're not careful despite a low voltage cut off and one inverter caught fire when…"
yesterday
Adam Woods replied to Dan Nate's discussion Charging Stihl tools from the van
"Easy... an inverter, something like this: https://www.ebay.co.uk/itm/376050861701?mkcid=16&mkevt=1&mk...
Just make sure you dont power too many batteries while the van is stationary..."
yesterday
Fusion Media posted a blog post
A team from Howardson Group is preparing to take on the formidable National Three Peaks Challenge in memory of their much-missed colleague, Joe Emery, who sadly passed away in July last year. The challenge will see the team scaling the highest…
yesterday
Dan Nate posted a discussion
So I'm doing some light domestic work using mostly Stihl AK powered gardening tools, I'm wondering if anyone can recommend a way to charge them up between jobs whilst driving between jobs. There's probably a very obvious way of doing it but I've…
yesterday
Fusion Media posted a blog post
Greg Fitzmaurice, dual-role Course Manager and General Manager at Hunley Golf Club in North Yorkshire, has dedicated 28 years to the greenkeeping industry.Since joining Hunley 12 years ago, Greg has overseen significant changes at the course,…
yesterday
Robbie posted a blog post
Sunday
Matthew Fairclough replied to Brian's Garden Maintenance's discussion Clients contracts for wet Grass cutting
"Totally agree with this Sam - I live in Scotland and there's absolutely no guarantee that leaving the grass another fortnight will lead to anything other than it being twice as long and potentially twice as wet! I've provided myself with what I…"
Sunday
Sam Bainbridge replied to Brian's Garden Maintenance's discussion Clients contracts for wet Grass cutting
"Dont do contracts for private gardens. I keep it simple "no problem but i wont be back until its your next turn and price per cut will be double to compensate for it being longer, however if its to wet again next time whats your plan?" 
that answer…"
Saturday
Joshua Fine is now a member of Landscape Juice Network
Saturday
Jason Taylor replied to Jason Taylor's discussion Lawn / soil problem
"Yes he has a clause saying we can revise the price based on previously unknown obstacles or things we weren't aware of at the time of quoting. Thus also included damage to machinery. The developer has already put a land drain in near their patio,…"
Saturday
More…

Lawn / soil problem

Hello all,my son has started a landscaping business. He's had a few jobs. The one we priced and is working on is a new build. The garden is pretty big, about 450m2.Our quote was to seed it, plant a hedge at the back and create a border around with…

Read more…
2 Replies · Reply by Jason Taylor on Saturday
Views: 125